(PDF) Study of Temperature and Chloride Concentration
AISI 316L is a type of stainless steel that is frequently used in various industries such as chemical industry, refining industry, marine industry, etc. AISI 316L known for its resistance to ...
Microstructure, Mechanical Properties, and Residual Stress …
2. Materials and Methods. AISI 316L alloy powder obtained by gas atomisation was used in this study. The morphology of the powder is shown in Figure 1, and the chemical composition is listed in Table 1.The powder diameter was ranging between 45 μm and 75 μm and had a good degree of sphericity that enabled a smooth powder …
Sintering Kinetics of Austenitic Stainless Steel AISI 316L …
AISI 316L stainless steel owes its very good corrosion resistance to high chromium and molybdenum content. ... TG thermogravimetric measurements, consisting of measuring the mass changes of the tested powder mixture as a function of time or temperature, allowed the determination of the impact of both the percentage composition …
The passivity of AISI 316L stainless steel in 0.05 M H 2 SO 4
Mott–Schottky plots of C −2 as a function of potential for passive films on AISI 316L formed at the potentials of 0, 0.2, 0.4, and 0.6 V in 0.05 M H 2 SO 4. Full size image. Figure 5 displays the donor density as a function of the formation potential. Similar values for the donor density have been observed, and the tendency of the donor ...
Additively manufactured hierarchical stainless steels with …
Supplementary Table 2 lists the typical composition of 316L SS fabricated by L-PBF from each machine, together with a reference AISI 316L sample 11. The overall composition of our L-PBF 316L SS is ...
Complex Corrosion Properties of AISI 316L Steel Prepared …
AISI 316L is a material with a very low corrosion rate under normal conditions. It follows from the aforementioned material characteristics that accelerated testing methods had to be used; otherwise the standard material immersion tests could take decades. Corrosion tests were performed on a Voltalab PGZ 100 with Voltamaster 10 software ...
316/316L Stainless Steel
Fabrication Data for Stainless Steel 316/316L. Alloy 316/316L can be easily welded and processed by standard shop fabrication practices. Hot Forming. • Working temperatures of 1700–2200°F (927–1204°C) are recommended for most hot working processes. For maximum corrosion resistance, the material should be annealed at 1900°F (1038°C ...
A Comprehensive Analysis of AISI 316L Samples …
Last Updated: 25 Nov 2023. PDF | Metal Fused Deposition Modelling is a promising multi-step process able to manufacture metal parts by means of a low-cost …
Tensile properties of 316L SS obtained under different rolling …
B. Ravi Kumar. Role of cold rolling texture on the tensile properties of the cold rolled and cold rolled and annealed AISI 316L austenitic stainless steel is described here. The solution-annealed ...
Predictive approach of high-cycle fatigue limit of finished turned AISI
This paper presents a global approach in order to predict the high-cycle fatigue (HCF) limit of turned parts. The multi-axial fatigue criteria of both Crossland and Dang Van are adapted for the case of machined parts. Thereby, the machined surface conditions which are residual stresses, superficial damage, and hardening, are taken into …
کارخانه muti function 316 ss
AISI 316L Stainless Steel Properties: Composition, Tensile Yield … Type 316L Stainless Steel Properties. Type 316L stainless steel density is 0.289 lb/in3 (8.0 g/cm3); melting point is 1375-1400 °C (2500-2550 °F); 0.2% yield strength is minimum 25 ksi (170 MPa) in annealed and hot finished condition, minimum 45 ksi (310 MPa) in annealed and ...
Multi-Material Additive Manufacturing: Creating …
Ferro, P.; Fabrizi, A.; Elsayed, H.; Savio, G. Multi-Material Additive Manufacturing: Creating IN718-AISI 316L Bimetallic Parts by 3D Printing, Debinding, …
Modeling and multi-response optimization of cutting
Request PDF | Modeling and multi-response optimization of cutting parameters in turning of AISI 316L using RSM and desirability function approach | In this study, the effects of different ...
muti function sus 304 سازنده
Muti-Function Solar Crawler Type Solar Hydraulic Ramming Dri BM1320 – Baumatic HK Functions SUS304 Stainless Steel Body Brass Ceramic Cartridge Black plating Body gauge: 3mm Maximum water pressure: 0.5Mpa Minimum water pressure: 0.1Mpa Related Products Related products BWF712W $ BWDI1418.1 $ BWDF2428 $ BTD45 $
Fatigue Behavior of Additively Manufactured Stainless Steel 316L
Fatigue life curves for L-PBF 316L, again considering only samples not subjected to heat treatment, are reported in Figure 2 for the machined or turned condition in which case R a is in the range of 0.6–1.8 μm and R z is 3.7–11 μm, although this essential information is not always reported [ 38, 40, 41, 51, 57, 67 ].
Influence of Heat Treatment of Steel AISI316L Produced by …
2.1. Powder Characterisation. The material used for the SLM was a 316L austenitic stainless-steel powder with particle size ranging from 15 to 45 μm [].The powder used was supplied by Renishaw (Wotton-under-Edge, U.K.) and was sieved several times.
AISI 316L Stainless Steel Properties: Composition, …
AISI 316L stainless steel is a modified ultra-low carbon Cr-Ni-Mo series austenitic stainless steel based on AISI 316. It is recommended for parts that cannot be annealed after …
AISI- SAE 316L Stainless Steel (UNS S31603)
The addition of molybdenum gives AISI 316L stainless steel improved corrosion resistance over 304/304L and 316/316L stainless steels. AISI 316L stainless steel is suitable for a wide variety of applications that …
Material No.: AISI 316L
Structure. austenitic. Corrosion. stainless. rustproof. non-corroding. chemically resistant. Description. Increased corrosion resistance to halogenated substances and oxidising acids, due to it's high molybdenum content in comparison to 1.4401/1.4404.
A Comprehensive Analysis of AISI 316L Samples Printed via …
Also, in this case, AISI 316L is widely used with FDM technology, as demonstrated by the scientific bibliography reported [91, 92]. Carminati et al. [93] have investigated the mechanical ...
Microstructure and Mechanical Properties of AISI 316L …
of AISI 316L produced via DED increased from 3 to 9 µm when the laser power increases [42]. Table 2 compares all the dendrite sizes t hat have been foun d in different stud ies.
Microstructure and Mechanical Properties of AISI 316L …
Milton et al. studied the microstructure of DED AISI 316L and revealed that Cr and Ni equivalent contents lie in the range of 5–10% δ-ferrite . Zietala et al. also investigated DED of AISI 316L and found that intercellular δ-ferrite formed at sub-grain boundaries as a consequence of its enrichment of Cr and Mo, and depletion of Ni .
Multi-pass butt welding of thick AISI 316L plates by gas …
In this study, it was aimed at producing good quality joints in 10 mm thick AISI 316 L ASS plates by the multi-pass GTAW method, which is commonly used in cryogenic LNG tanks. For this purpose, 10 mm thick AISI 316 L ASS plates were joined by the GTAW method using a filler rod of ER316L with a diameter of 2.4 mm at five passes.
Applied Sciences | Free Full-Text | Functionally Graded AISI 316L …
AISI H13 hot-work tool steel and AISI 316L low-carbon stainless steel powders were employed as feedstock materials to produce the FGM deposit over an AISI 1045 mild steel substrate. The powder particle size of the feedstock employed was 53–150 µm for the AISI H13 powder and 45–125 µm for the AISI 316L powder.
Stainless Steel AISI 316L
Elongation at Break. 50%. @ Room Temperature, varies with thickness. Thermal Conductivity. 16 W m -1 °C -1. @ Room Temperature. Thermal Expansion Coefficient. 17.2 x 10 -6 °C -1. RT to 200°C.
(PDF) Prediction of Model Distortion by FEM in 3D Printing …
the AISI 316L material, as well as for the AAS, by the manufacturer. The onl y necessary input from the user is the input o f the machine type (fo r setting the working spac e), the
Microstructure and Mechanical Properties of AISI …
The data show that building conditions play key roles in the determination of the microstructure and mechanical characteristics of the final components produced via …
SS 316L Type 316L, WNR 1.4404, UNS S31603, AISI …
techniques 316L stainless steel can be hot worked. The hot working temperatures should be between 1150-1260 °C and should not be less than 930 °C. Mechanical Properties SS 316L Type 316L, WNR 1.4404, UNS S31603, AISI 316L, ASTM 316L, Grade 316L, AFNOR Z 2 CND 17-12, ALLOY 316L WNR 1.4404 UNS S31603 ASTM 316L AFNOR Z 2 CND 17 …
AISI 316 Stainless Steel Properties, SS 316 Grade Density, …
316L stainless steel (UNS S31603) is the low carbon version of AISI 316. SS 316 is better than SS 304 in terms of corrosion resistance, heat resistance and certain properties, but the price is higher than AISI 304, for more details, please check stainless steel grade 304 vs 316, and 316 vs 316L. SS 316 Data Sheet & Specification
Pitting Corrosion of Type 316L Stainless Steel Elaborated …
Microstructures. 316L(WS), 316L(SLM) and 316L(SLM-1050) have comparable carbon content (150-160 ppm in Table 1) and very low sulfur level (< 50 ppm in Table 1).The pitting resistance equivalent number (PREN) of 316L(SLM) and 316L(SLM-1050) is significantly greater than that of 316L(WS), Table 1.The difference (of about 3) …
Additive Manufacturing of AISI 316L Stainless Steel: …
AISI 316L is a type of austenitic steel widely used in industries such as aerospace, medical, automotive, and marine due to its excellent corrosion resistance and …
AISI 316 Stainless Steel: Specification and Datasheet
Uses for SS AISI 316. Also known as surgical stainless steel, marine steel, 316S16 (as per the British Standard), SS 316 is an austenitic chromium-nickel alloy. As a consequence it: Has a very high corrosion resistance. Is generally nonmagnetic. Can perform well at a very wide temperature range (-150 to 950 °C).
Prediction of Microstructure for AISI316L Steel from
A thermal model was developed by Scipioni Bertoli et al. in order to express solidification parameters G and R as a function of the process parameters ratio P/v (laser power/scan speed). This provides a guide for the selection of the process parameters for 316L steel manufactured via L-PBF.
Mechanical Properties of AISI 316L Lattice Structures …
Herein, we studied the mechanical behavior of stainless-steel (AISI 316L) lattice structures both experimentally and computationally. The lattice architectures were body-centered …
Layer-level AISI 316L-18Ni (300) Maraging multi …
Layer-level AISI 316L-18Ni (300) Maraging multi-material fabrication via Laser-Powder Bed Fusion. Intralayer multi-material fabrication on traditional L-PBF …
Wear Maps and Statistical Approach of AISI 316L Alloy …
Dry Wear Test. Wear tests on the AISI 316L stainless steel were performed at room temperature (25 °C) and 50% relative humidity using a Bruker/UMT-2 universal tester under ball-on-flat dry sliding conditions (Fig. 2) in a stroke length of 10 mm. Prior to wear tests, all the samples were metalographically prepared (abrasive paper and …